10TPH Reverse Osmosis Filter Water Filtration System

Min Order

1
Product Unit

Pieces
Origin

China Mainland
Payment
Contact Now Start Order

Description

Product Detail

CK-RO-10T Reverse Osmosis Water Treatment

1. Design Basis

n Raw water source : well/groundwater

n Raw water analysis report : unconfirmed

n RO system rated flux : 10 m3/h

n RO system recovery : 50-65%

n Salt rejection : 96%-99%

n RO working voltage : 220V/380V/50Hz

n RO system power : 5.1KW

n Water feeding pressure : 0.15-0.25Mpa

2. Flow Chart Of RO Water Treatment Machine

???????.png

3. System Configuration

u Raw water supply pump: To use CNP.

u High-pressure pump: To use CNP.

u Reverse Osmosis Membrane: To use VONTRON, China

u Pretreatment device: To use FRP tank with automatic valve.

u Conduit: To use SS304.

u Electric standard configuration: PC automatically control

u Electrical components: To use Zhengtai’s and Schneider’s products.

u Frame: To use stainless steel.

4. Brief Introduction to the Equipment

IMG_20131220_135120_??.jpg

IMG_20131220_135416_??.jpg

Recovered_JPEG Digital Camera_4134_??.jpg

5.1 Raw water pump

In order to ensure the system of water flow and pressure rating and set

5.2 Multi-media filter

The multi-media filter is widely used in drinking water treatment to remove different types of particles, such as suspended solids (turbidity), colloidal compounds and etc, ensuring the filtered water’s TDS is less than 5. This process will reduce the load on the back-end fine filters.

Diffuser

There is diffuser, installed in the filter. Their main function is to make the compressed air and the water distribute evenly during backwash and water distribution.

5.3 Active Carbon filter

The active-carbon filter is the key device, commonly used for removal of organic substance and heavy metal element, suspended solids, residual chlorine and etc. It can effectively reduce the level of COD and improve the taste of water. The system is a pressure filter. In the filter, the quartz and Coconut shell active carbon bed are employed. The activated carbon is equipped with vent valving at the highest point and a drain connection at the lowest point. The internal systems and components for each tank is constructed of FRP.

Diffuser

There is diffuser, installed in the filter. Their main function is to make the compressed air and the water distribute evenly during backwash and water distribution.

5.4 Water softener filter

Ion exchange resin is used in water softening system for Ca+?Mg+ and other cation exchange. To prevent undissolved salt from depositing in the surface of reverse osmosis membrane ,the resin which ensures well permeable ability of membrane module after it works a long time and extends lifetime of membranes , enhances quality stability of ro purified water . Water softener is vertical structure which use frp material , produced as vessel standard, designed pressure for 8kg/cm2 that American auto valve is used for full-automatic salt regeneration .

5.5 Security filter ( Cartridge Filters)

The security filter is most commonly used for treat water. The whole system adopts one set of stainless filter. There are 2 pieces of polypropylene in every 5µ filter cartridges, filtering the vast majority of particles in the water, which eases the load of RO membrane. This process of filtration benefits to the filter cartridge and prolongs its lifetime in the system.

This apparatus contains filtration component and stainless support layers. The support layer is made of stainless steel 304, with the advantages of compact structure, beautiful shape, high flux, good filtration accuracy and etc. This apparatus is fitted with air drain valve and bottom air drain valve and side drain valve.

5.6 High pressure

In order to ensure the system of water flow and pressure rating and set

5.7 Reverse Osmosis Modules( RO)

RO system is key part for the water treatment system, which is widely used to make the pure water and drinking water. RO membrane removes many types of large molecules and ions from solutions by applying pressure to the solution when it is on one side of a selective membrane. The result is that the solute such as iron, Virus, bacteria and solids is retained on the pressurized side of the membrane and the pure solvent is allowed to pass to the other side.

5.8 Piping, Valves & Fittings

The pipe, valves and fittings (including tubing) ball valves, butterfly valves, piping used to the system is SS304. Reverse Osmosis Modules is equipped with sample valve for the convenience to check the product water.

5.9 Control devices

The whole automatic production line is achieved through the converter and PLC programmer and data collector such as the liquid lever sensor, flow sensor and etc. The whole production line is monitored by remote computer. When the water level of the product water tank is high, the system will stop automatically. When the water level of the product water tank is low, the system will run automatically.

Remarks:

5. Consumables Replacement Cycle

Description	Change time
Quartz sand	should be replaced every about 15 month	50kg/bag
Activated carbon	should be replaced every about 15 month	50kg/bag
Filter cartridge	should be replaced every about 1 month
RO membrane	should be replaced every about 1.5-2 years

6. Technical training

??1(????????)_??.jpg

??2.jpg

1. Supplier provides technical training for free; we are responsible to provide site training for personnel of buyer, until they are of good operation skills.

2. Supplier provides training for maintenance people; if the training carries out at the supplier’s site, the buyer is responsible for their travel expense.

3. Training content:

Ø Basic theoretical knowledge of reverse osmosis

Ø Equipment structure

Ø Membrane cleaning

Ø Installation, debugging, operation

Ø Maintenance, repair

7.Product Accessories

Different accessories are used in water treatment machine. Cartridge filter housing,Ozone generator,Brine tank, meter flows,Pumps, , UV etc.

8. Introduction:

????1.jpg

9. After-sales service commitment

photobank (1).jpg

1. Quality assurance: as a good supplier of cosmetics machinery and equipment, I promised to provide the original products are the original packaging, in line with national quality certification system, and provide technical information related to the product description.

2. Supply and installation: product manufacturing and testing are quality records and testing information. The detection of product performance, we have the whole process of the product, the whole performance check, until the product was confirmed after the qualified packing.

3. Product delivery: as far as possible according to customer requirements, if any special requirements, I Division can be specially organized production, installation, and strive to meet the needs of users.

4. The warranty commitment: Division I supply agreement within the validity of the products provided by the one-year warranty (non-quality problems and consumables except), and I provide all the products are provided for normal working days after-sales service support.

5. The service system: as a good supplier of cosmetics machinery and equipment, I provide all the products provided by the perfect after-sale protection system; when the equipment failure, if necessary, I will be assigned to the Secretary for professional technicians short time For your home repair or repair.