Motor Driver For Nema 2M423A

Min Order

1
Product Unit

Pieces
Origin

China Mainland
Payment
Contact Now Start Order

Description

Product Detail

2M432A

Characteristic :

1.Using new digital sinusoidal micro-segmentation algorithm
2.Lower heating and noise , higher stability
3.The phase current can be adjusted by switch DIP.
4.For the input control signal, electric circuit use optically coupled isolator to low the noise interference .
5.With short circuit, overvoltage, undervoltage, overtemperature protection and improving functions
stepper Motor driver Specification :

Input Power supply :	12-40VDC
Output Current	0.4A~3.2A
Drive Way	PWM constant current chopping ,two phase Sine wave output current
Suitable stepper motor	35,42,57 series two phase stepper motor
Ambient environment	-10?~55? 15~85%RH?No condensation. Non-corrosive, flammable, explosive, conductive gas, liquid and dust
Keeping enviroment	-40?~+55?, <93%RH,No condensation, no frost
Size (LWH)	1156824mm
Net Weight	0.25 Kg

Curent seting :

SW1-SW3	000	001	010	011	100	101	110	111
Phase current	0.4A	0.8A	1.2A	1.6A	2.0A	2.4A	2.8A	3.2A

Microstep Subdivision setting :

SW1-SW3	000	001	010	011	100	101	110	111
steps/rev	2	8	10	16	20	32	40	64

Describtion :

Microstep setting	Users can set the driver Microstep by the SW1-SW5 five switches,total 28 micro-step. When you set the microstep , pls stop the driver working?The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure .
Output current setting	Users can set the driver Microstep by the SW1-SW5 five switches. The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure..
Double pulse setting	SW7 sets pulse mode, setting “on'' as double pulse mode, setting “off'' as pulse + direction mode.,CW+/CW is Clockwise ,CCW+/CCW- is Counterclockwise , need to confirm the wire of stepper motor ?
Automatic half current function	Users can set the driver half flow function by SW6. "OFF" indicates the quiescent current is set to half of the dynamic current, that is to say, 0.5 seconds after the cessation of the pulse, current reduce to about half automatically. "ON" indicates the quiescent current and the dynamic current are the same. User can set SW6 to "OFF", in order to reduce motor and driver heating and improve reliability.
Self test function	When SW1-SW5 is OFF , Inner of drive send 1K pulse to test whether the motor,wire,and self is normal?
signal Interface	PUL+ and PUL- are the positive and negative side of control pulse signal; DIR+ and DIR- are the positive and negative side of direction signal; ENA+ and ENA- are the positive and negative side of enable signal .
Motor Interface	A+ and A- are connected to a phase winding of motor; B+ and B- are connected to another phase winding of motor. If you need to backward, one of the phase windings can be reversed .
Power Interface	It uses DC power supply,recommended working voltage is 12-40VDC,power is over 50W,voltage shouldn’t be over 40VDC and below 12VDC?
Indicator Lightor	There are two indicator lights. Power indicator is green. When the driver power on, the green light will always be lit. Fault indicator is red, when there is over-voltage or over-current fault, the red light will always be lit; after the driver fault is cleared, if re-power the red light will be off.?
Installation	The size of motor driver is 115×68×24 mm,mounting holes is 100mm?Chest and upright installation are ok,we suggest upright installation? During installation, it should be close to the metal cabinet for heat dissipation.