13MM Electric Mixer
-
Min Order
1
-
Product Unit
Pieces
-
Origin
China Mainland
-
Payment
- Contact Now Start Order
- Favorites Share
- Description
Product Detail
Product Description | |
Model: | HK-D06 |
Rated Volatge: | 220-240V |
Frequency | 50/60HZ |
Rated Input Power: | 1100W |
Drilling diameter: | 1-13mm |
No Load Speed: | 0-950R/min |
G.W./N.W.: | 18/17 |
Packing | 34.5*26.5*52cm |
Drill maintenance
Electric drill due to ventilation and heat, long-term use of very large internal dust, dust and gears (bearings) will slip on the lubricating oil mixed deterioration of dry wear and increase wear and tear, especially the alternative to use even worse. In order to ensure the rotation precision of the electric drill and reduce the excessive clearance caused by the abrasion of the bearing (sleeve), it is very necessary to keep the clean interior and greasing lubrication.
method:
Loosen the drill outside a few self-tapping screws or screws; lay flat to lift half of the shell; general structure of the new type of hand drill is semi-embedded, that is, all the machines, electrical components are installed in the other half of the shell
Carefully remove the carbon brush, and then take the drill chuck this end, and then gently lift the motor to remove the rotor (do not touch the enameled wire), clear the commutator rotor (with carbon brush contact that is), if dirty Or wear and tear can be polished with emery cloth and then sandpaper or metallurgy sanding to light.
Rotor before and after the bearing if the seal can be wiped clean the outside, if the seal should be replaced promptly broken. Wipe the helical gear shaft in front of the rotor
Clean the oil inside the case. Clean the helical gear and the bearings (or bushings) on both ends of the drill chuck rod.
Reinstall the unloaded parts, first install the rotor; then install the drill chuck helical gear; equipped with carbon brushes, carbon brushes shorter than 7-8 mm to be replaced in time. Brush to be flattened, and finally find a little "Mobil" or "Shell" grease added between the gear and bearing (or sleeve) All parts to be flattened Check the correct installation of the other half, Tighten the screws, hand movement feel no delay, it can power test.
- Cloth Grommet 1 Pieces / (Min. Order)
- NC Electric Winder 1 Pieces / (Min. Order)
- NC Electric Winder 1 Pieces / (Min. Order)
- Electric Winder 1 Pieces / (Min. Order)
- Electric Drum Series 1 Pieces / (Min. Order)
- Electric Griddle WEG24 1 Pieces / (Min. Order)
- Electric Griddle WEG36 1 Pieces / (Min. Order)
- Electric Warmer 1 Pieces / (Min. Order)
- Electric Tow Tractor 3T 1 Pieces / (Min. Order)
- Electrostatic Fume Purifier 1 Pieces / (Min. Order)
- Electric Push Cylinder 1 Pieces / (Min. Order)
- Folding Electric Towel Warmer 1 Pieces / (Min. Order)
- Small 9V Piezoelectric Transducer 80dB 1 Pieces / (Min. Order)
- Mini 9V Piezoelectric Transducer 1 Pieces / (Min. Order)
- High DB 5V Piezoelectric Transducer 1 Pieces / (Min. Order)
- Small 10V Piezoelectric Transducer 1 Pieces / (Min. Order)
- 10V Piezoelectric Transducer 90dB 1 Pieces / (Min. Order)
- Electric Aroma Lamp Diffuser 1 Pieces / (Min. Order)
- Ground-Grid Electric Bumper 1 Pieces / (Min. Order)
- Electrician's Tool Set 1 Pieces / (Min. Order)