2835 LED Package

Product features:

  *The LED are available with different color
  *Utilizing advanved technology
  *High brightness,long life

Package Outline    

Unit:mm

NOTES:  

1. All dimensions are in millimeters;   

     2.Tolerances are±0.05mm unless otherwise noted.

? Typical optical characteristics curves 

Requirements for application and reflow soldering

After reflow soldering rapid cooling should be avoided

Use the following conditions shown in the figure.    

      <Pb-free solder>                                       <Lead solder>

1.Reflow soldering should not be done more than two times    

2.When soldering,do not put stress on the LEDs during heating

Handling Precautions

Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.

? Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.

? Do not stack together assembled PCBs containing LEDs. Impact may scratch the silicone lens or damage the internal circuitry.

? Not suitable to operate in acidic environment, PH<7.

? LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.

When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine 

element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than  375 PPM.

? The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.

? Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.

Storage

? Before opening the package, the LEDs should be kept at 30? or less and 60%RH or less. The LEDs shouldbe used within a year.

? After opening the package, the product should be stored at 30? or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30?or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.

Reliability

(1) TEST ITEMS AND RESULTS

2)  CRITERRIA FOR JUDGING THE DAMAGE 

U.S.L.:Upper Standard Level              L.S.L.:Lower Standard Level

Application

?LED Panel light

?LED bulb light

?LED tube light

?LED strip light

?LED spot light etc.

Packaging & Delivery

Packaging Details

4000pcs/reel, each reel Anti-static vacuum Bag

Delivery Time

Shipped in 3-5 days after payment

Cautions:

1)Soldering Conditions

Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and Second soldering process.

2)Static Electricity

It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.All devices, equipment and machinery must be properly grounded.Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) 

3)Moisture Proof Package

It is recommended that moisture proof package be used .

4)Storage

Before opening the package ,The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be used within a year.

5)After opening the package, The LEDs should be soldered within 24 hours (1days) after opening the package.

FAQ:

Q1. Can I have a sample order for led light?

A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.

Q2. What about the lead time?

A:Sample needs 1-3 days, mass production time needs 5-7 days for order quantity more than 100KK.

Q3. Do you have any MOQ limit for led light order?What's the Payment way ?

A: MOQ is 100pcs for each model. We accept T/T Paypal and Western Union three ways paymant

Q4. How do you ship the goods and how long does it take to arrive?

A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 2-5 days to arrive. Airline and sea shipping also optional.

Q5. How to proceed an order for led light?

A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.

Q6. Is it OK to print my logo on led light product?

A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.

Q7: Do you offer guarantee for the products?

A: Yes, we offer 3 years warranty to our products.

Our Services:

?Reply your inquiry in 24 working hours

?Well-trained and experienced staffs to answer all your inquiries in fluent English.

?Strict quality control procedures before shipment.

?Customized design is available.OME and ODM are welcomed

?Delivery the goods to our customer all over the world with speed and precision.

Company:

Patents:

Contact:

Alisa Huang

Guangdong Elite Optoelectronic Technology Co., LTD

Mobilephone:+86-18033336027

Tel:0769-89080660-824

Fax:0769-89080658

Email:ruilu_sales1@elitebm.com

Contact: Carol Chen

Mobilephone:+86-13798703095

Telephone:+86-769-88941998

Email:elite1@elitebm.com